Posts

Injection Mold Design

Plastic injection molding for producing plastic products

Plastic injection molding is the principal process for producing plastic products or parts of products. Plastic is acknowledged to be a very flexible and cost-effective material that is used in many applications. Although the tooling can be expensive, the cost, per part is very low. Intricate geometries are limited only to the abiltiy to create the injection mold. Things you use everyday, such as the case that houses your monitor, the keyboard on which you type or the mouse on your desk were produced with plastic injection molding.

Plastic injection molding involves the transformation of a plastic solid, usually in the form of granules or pellets, and heating the plastic resin to a specific temperature until it melts. The melt is then forced into a mold made up of two or more dies, where it is forced to “cool”, resulting in producing the desired shape. A specific amount of time passes, usually a few seconds, and the mold is then opened and the part is released. This cycle then repeats continuously until the desired quantity is reached.

Considerations of  Injection Mold Design

The design of the part, and therefore the mold, needs to include draft features (angled surfaces) to make possible the removal of the part from the mold. Typical draft angles are about 1 to 2 degrees for part surfaces which do not exceed five inches. Dimensional tolerance specification will dictate the final cost of the part as well as its ability to be manufactured. If there is a small section of the part which needs higher tolerances, such as the location of a critical feature used for alignment,do not specify a tight tolerance, as an alternative, plan and design for post molding processes such as machining to achieve the desired results.

Radii and Corners

It is very important that uniform wall thickness be maintained at the corners. The internal and external radius need to share the same center point. External radii = internal radii + wall thickness. The minimum radii should not be less than ¼ of the minimum wall thickness. Design for radii to be ½ to ¾ of the nominal wall thickness. When a large amount of stress is going to be present, it is very important to design in larger radius as this will distribute the stress much more evenly.

Wall Thickness

The production of thin wall items such as a clamshell for retail packaging are possible with today’s technology. Products with thick walls are also easily produced. However, parts which require uneven wall thickness present a challenge to the plastic molder manufacturer. Creating a part with a uniform wall thickness and cross section will abridge manufacturing and reduce costs. One issue to be aware of is sinking. Wherever an intersection or “tee” occurs, there will be some degree of sinking. This occurs because thicker walls cool at a slower rate and therefore create this problem.

Ribs

Ribbing should be ½ to two thirds of the nominal wall thickness and less than 3 times the thickness in height.A taper of 1° is usual. Note: as mentioned above, excess thickness can result in shrinkage.An excess in rib height combined with a taper will produce thin areas requiring extra fill time at the mold.

Weld (Part) lines

The location of weld lines needs to be considered by designer before a injection mold is created. Weld lines are formed by the joining of the flow fronts of the plastic during molding. One issue of concern is the that the weld line area is more susceptible to cracks and stress failure.

Bosses

  • Diameter = (Outside Diameter) \ (Inside Diameter) = 2 to 3
  • Thickness = 1/2 to 2/3 nominal wall thickness
  • Gusset Height = 2/3 Height
  • Height = Fastener minimum requirements
  • Taper = 1 deg. all around
  • Diameter Ratio should be minimum ratio of 2., this will reduce risk of failure.

Pressure:

Another factor in the design will be the clamping pressure required to produce the part while the plastic is being injected. Smaller cavities can result in high pressures being required to force the plastic or rubber material to fully fill the mold cavity. This will, in turn, determine the thickness of the mold material, usually steel) as well as the type of machine in which can be used.

Summary:

Many factors must be taken into account when designing a mold for the creation of plastic injection molded parts. Factors such as draft angles, wall thickness, ribbing (not the kidding kind), bosses and weld lines and clamping pressure all come into play when designing a mold that will be used in a plastic injection mold machine. Each facet is important in and of itself, but as a whole, each one affects the others. Therefore the design of a mold for plastic molding can be quite involved. When done correctly, the result will be a mold which will yield thousands, hundreds of thousands, or even millions of parts over it’s lifetime.

Contract Injection Molding

Contract Injection Molding

When you are looking for a company to do a terrific job handling your custom injection molding contract. You want to make sure that they can cover your needs. If at all possible, tour the facility of where you are interested in having your work done. But you want to make sure their facility can handle the load.

You want a company that handles both a large and small volume of work. Some companies only will do a certain amount of work therefore they turn down small amount jobs. You want them to provide samples, you want to be able to see what kind of job they will do for you before you contract a huge order and do not like the work.

You want full production abilities, process optimization, and Insert molding and over molding, PPac capabilities. You also want packaging and domestic and international shipping capabilities. The company that you contract for your work, you want to handle the type of job you have for the price that you want.

That is why it is important to tour the facility to see first hand how the company will handle your job load. You want a guarantee that the job you give them will be nothing less than spectacular. This is what contract Plastic molding is all about.